Products

MQ135 Gas Sensor module for Air Quality having Digital as well as Analog output. Sensitive material of MQ135 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensors conductivity is more higher along with the...

This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ2 Smoke & Flammable gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins...

This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ3 Alcohol gas sensor as a alcohol gas sensing element. It requires no external components just plug in Vcc & ground pins and...

This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ4 Methane gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you...

This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ5 gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you are...

This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ6 LPG gas sensor as a gas sensing element. It requires no external components just plug in Vcc & ground pins and you...

This Carbon Monoxide (CO) gas sensor detects the concentrations of CO in the air and ouputs its reading as an analog voltage. The sensor can measure concentrations of 10 to 10,000 ppm.The sensor can operate at temperatures from -10 to 50°C and consumes less...

This sensor module has an MQ-8 as the sensor component and has a protection resistor and an adjustable resistor on-board. A sensitive material MQ-8 Hydrogen H2 Gas Sensor Module use in clean air low conductivity tin oxide (SnO2). When there is the environment in...

MQ-9 gas sensor module has high sensitivity to Carbon Monoxide, Methane and LPG. Sensitive material of MQ-9 gas sensor is SnO2, which with lower conductivity in clean air.  It makes detection by cycling high and low temperature, and detects CO when low temperature (heated by...

The MT3608 2A Max DC-DC Step Up Power Module Booster Power Module is a low-cost module that can step-up a 2 to 24V input voltage up to a 5 to 28V output at up to 2A. DC-DC boost converters step up the input voltage...

The Nano 328P Expansion Adapter Breakout Board IO Shield acts as a breakout board for the Arduino Nano microcontroller. There are several different options for power input and the footprint of this board is the same as the Arduino Duemilanove. In addition, each pinout includes 5V and GND pins for easy...

The Arduino Nano with USB Type-C is a compact and breadboard-friendly microcontroller board based on the ATmega328P chipset. This version features a modern USB Type-C connector, providing more durability and easier connection. It includes the CH340 USB-to-Serial converter for reliable PC communication and programming. Ideal for embedded electronics projects, this...

NE555 Time Delay Monostable Switch with Electrical Relay 12V is a monostable generator based on the NE555 integrated circuit. The power indicator LED and switch trigger timing indication LEDs. Timing from microseconds to long hours.  This is a monostable generator based on the NE555...

NE555 Delay Timer Switch Adjustable 5V Relay Module Introducing the NE555 Delay Timer Switch Adjustable 5V Relay Module, your go-to solution for accurate timing control across various applications. Powered by the dependable NE555 chip, this module delivers excellent timing performance and features LED indicators...

The NE555 SMD devices are precision timing circuits capable of producing accurate time delays or oscillation. In the time delay or monostable mode of operation, the timed interval is controlled by a single external resistor and capacitor network. In the a stable mode of...

This is a complete GPS module that is based on the NEO-6M. This unit uses the latest technology to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is...

The NodeMCU ESP8266 LUA Amica WiFi Development Board with CP2102 USB-Serial Interface has powerful onboard processing and storage capabilities that allow it to be integrated with the sensors and other application specific devices through its GPIOs with minimal development up-front and minimal loading during...

NodeMcu ESP8266 V3 Lua WiFi Development Board Introducing the revolutionary NodeMcu ESP8266 V3 Lua Wifi Dev. Board! This cutting-edge, low-cost WiFi technology uses a modern, high-level and mature LUA-based programming. It has all the resources on board and I/O pins you need to enhance...

NRF24L01 2.4GHz Antenna Wireless Transceiver Module is a highly integrated, ultra-low power (ULP) 2Mbps RF transceiver IC for the 2.4GHz ISM (Industrial, Scientific, and Medical) band. With peak RX/TX currents lower than 14mA, a sub μA power down mode, advanced power management, and a...

P10 Green High Brightness  LED Display Panel Module - 32x16 - 2835 SMD LEDs - 5V - Dot Matrix Display P10 32x16 (Total 512 2835 SMD LEDs) LED Display module is the easiest way to put together any size of Outdoor or Indoor LED display...

P10 SMD LED Display Module RGB Color P10 SMD LED Display Module RGB Color P10 32×16 (Total 512 LEDs) LED Display module is the easiest way to put together any size of  Indoor LED display signboard. This panel is having a total of 512...

P10 Pink High Brightness  LED Display Panel Module - 32x16 - 2835 SMD LEDs - 5V - Dot Matrix Display P10 32x16 (Total 512 2835 SMD LEDs) LED Display module is the easiest way to put together any size of Outdoor or Indoor LED display...

P10 RED High Brightness  LED Display Panel Module - 32x16 - 2835 SMD LEDs - 5V - Dot Matrix Display P10 32x16 (Total 512 2835 SMD LEDs) LED Display module is the easiest way to put together any size of Outdoor or Indoor LED display...

P10 White High Brightness  LED Display Panel Module - 32x16 - 2835 SMD LEDs - 5V - Dot Matrix Display P10 32x16 (Total 512 2835 SMD LEDs) LED Display module is the easiest way to put together any size of Outdoor or Indoor LED display...

A float switch is a device used to sense the level of liquid within a tank, it may actuate a pump, an indicator, an alarm, or other devices. Use them with hydroponics, saltwater tank, freshwater tank, gardening, aquariums for power head control, pet bowls,...

P80NF55 power MOSFETs have been developed using STMicroelectronics’ unique STripFET process, which is specifically designed to minimize input capacitance and gate charge. This renders the devices suitable for use as primary switch in advanced high-efficiency isolated DCDC converters for telecom and computer applications, and...

PAM8403 5V Two Channel Stereo Audio Amplifier Module is based on PAM8403 which is a 3W, class-D audio mini amplifier. It offers low THD+N, allowing it to achieve high-quality sound reproduction. The new filterless architecture allows the device to drive the speaker directly, requiring...

PAM8403 Mini 5V Audio Amplifier Board with Switch Potentiometer has a small digital amplifier chip, high-definition sound quality highlights the advantages of digital chips, circuit using the most reasonable peripheral configuration, power supply filtering is upgraded to 470uf. This PAM8403 Amplifier module differs from...

PAM8610 Digital Stereo Class-D Amplifier Board 2x15W Output is a 15W (per channel) stereo Class-D audio amplifier with DC Volume Control which offers low THD+N (0.1%), low EMI, and good PSRR thus high-quality sound reproduction. The 32 steps DC volume control has a +32dB...

This is a PC817 2 Channel Optocoupler Isolation Board. Onboard with 4-Channel 817 are independent, so they can achieve different voltage control at the same time. Using 4-way 817 optocoupler, to achieve the control signal and the control signal isolation, you can directly use...

Features  This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers Terminal block for power input (or you can use the 0.1″ breakouts on the side) Reverse polarity protection on the terminal block input Green power-good LED 3 pin connectors in groups of...